planethaser.blogg.se

1. Java x application could not launch driver#
2. Java x application could not launch full#
3. Java x application could not launch password#
4. Java x application could not launch windows#

Note: If the service is not started, register the correct XML port on the server and restart the service.Ĭomplete the following procedure to check that the Web Interface XML configuration is set properly:Įnsure that the correct XML broker(s) are listed under server. Open Services.msc from the XML broker(s) (XenApp Server).Įnsure the Citrix XML service is started. You can also try disabling the NetScaler global setting USIP (Use Source IP) mode.Ĭomplete the following procedure to ensure that you have registered the correct port on the XenApp 6 server(s): Ensure that the policy which enables the session reliability is set first (lower number in AppCenter console). When a server is booted and already placed in the correct Worker Group, where the Session Reliability is enabled, and the XTE service is not started, check the order in which the policies are applied. Error 2 - Resolution 3 Restart IMA service after the server is moved to the Worker Group that has Session Reliability enabled to resolve the issue.

If Session Reliability is enabled, XTE service is required to broker the connection to the XenApp Server. Click Start > All Programs > Citrix > Administrative Tools > ICA Listener Configuration.Ĭheck the XTE Service status.

Java x application could not launch windows#

Right-click, navigate to properties and verify all network adapters are selected.Īfter verifying all Network Adapters are selected, review the ICA adapters (only applies to XenApp 6 / Windows 2008 R2 圆4). Open Administrative Tools from the XenApp Server(s).Ĭlick Remote Desktop Session Host Configuration. then bind specific network adapter to the ICA listener. Important: If only one NIC is allowed for ICA traffic based off of network rules, firewalls, etc. Verify RDP and ICA listeners network adapter configuration. There could be a problem with performance counters that an Advanced Load Evaluator relies on. If an advanced load evaluator is used, change to a default load evaluator based only on user load and load throttling. Run qfarm /load to ensure load is not 20000 Note: 20000 indicates it is a licensing issue.Ĭlear Local Host Cache on all servers in farm to ensure a fresh copy of the Data Store subset is applied to the XenApp and Zone Data Collectors. ” Error 4Įrror: An error occurred while making the requested connection. “All the Citrix XML Services configured for farm failed to respond to this XML Service transaction. The specified Citrix XML Service could not be contacted and has been temporarily removed from the list of active services.

This message was reported from the XML Service at address. If the XML Service is configured to share ports with Microsoft Internet Information Services (IIS), verify that IIS is running. Verify that the Citrix XML Service is running and is using the correct port. “An error occurred while attempting to connect to the server on port. If you cannot logon, contact your help desk.”Įvent logs on Web interface might display:

Java x application could not launch password#

“Please verify your user name and password and try logging on again.

Java x application could not launch driver#

Protocol Driver error”Įxternal connections through the NetScaler fail with a "protocol driver error" while internal connections to the same XenApp server are still successful. “Unable to Launch your application, Contact your help desk with thefollowing information: Cannot connect to the Citrix XenApp server. If you continue to receive this message, contact your Citrix administrator." Error 2 Try to connect again after a few minutes.

Java x application could not launch full#

The Citrix XenApp servers are reporting full load and cannot accept your connection at this time. “Cannot connect to the Citrix XenApp server. Wrong class name − You might have specified the wrong class name.Unable to open published applications from XenApp 6.x and one of the following error messages might be displayed: Error 1 class file (just name) which is in the current directory.įollowing are the scenarios where this error could occur − To avoid this error, you need to specify the absolute (including packages) name of the. class file with the specified name then a run time error occurs saying “Could not found or load main class” error as − D:\sample>java ExampleĮrror: Could not find or load main class ExampleĬaused by: : Example Solution While executing, when JVM does not find a. Then you need to execute it using the java command as − java class_name Once you resolve them and compile your program success fully, an executable file with the same name as your class name is generated in your current folder, with the. Once you write a Java program you need to compile it using the javac command, this shows you the compile time errors occurred (if any).